The Best Methods for Hanging Wallpaper

Line an area with background and you’ve got instant decoration. From blah to daring in a matter of hours, newspaper could push boundaries beyond what paint can do. It enlivens walls with textures or patterns or both–your pick.

But as frequently as homeowners try to hang paper themselves, they rarely get it right, cursing their peeling seams and mismatched patterns–it is enough to drive you up a wall. Enter John Gregoras, a pro newspaper hanger from Somers, New York, with almost two years’ experience. And, boydid we learn a lot – everything from the way he plans the design to how he lines up the last seam. With this kind of insider know-how, papering only got a whole lot simpler.

Greatest Wallpaper Techniques roomgood.ru Overview

Layout is your secret if you are learning how to hang wallpaper. Paying attention to the sequence where the newspaper goes up ensures that your pattern will remain well-matched and seem straight. John Gregoras recommends functioning in one direction around the space to keep the pattern consistent.

But no matter how good your strategy, the pattern between the first and final strip will seldom match up. For that reason, Gregoras always starts his job behind a door, papering out from the corner till he reaches the space over the door– the least conspicuous place in the room.

Very often, the last strip of paper onto a wall isn’t a complete sheet. Another wallpapering tip Gregoras uses would be to constantly paper the corners together with broken sheets.

Click button at top to enlarge illustration.

Apply Wallpaper Paste

Paint the entire room with a wall primer/sizer.

Unroll the background. As you do, check for defects and drag the paper against the border of your worktable to remove the curl.

Cut the paper into sheets 4 inches longer than the height of your walls. Cut at precisely the exact same region on the replicate so patterns on adjoining sheets will line up.

Lay a cut sheet onto the table, face down.

Tip: Do not allow paste to get on the table or it will mar another sheet (wipe it off with a barely damp sponge if it does). Slide the paper all the way to the border of the table to apply paste to the ends and edges.

Novel the Paper

Fold the pasted back of the paper onto it, bottom and top ends assembly in the middle. Guarantee that the side edges line up perfectly. Smooth the paper onto itself as much as you can without creasing the springs.

Place the paper apart to permit the glue to soak in and also the paper to relax. Make sure you adhere to the exact booking time advocated on the wallpaper’s label, which differs based on its material (much more for vinyl-coated wallcoverings, less for uncoated papers).

Align First Strip

Start in a corner near your doorway. If the doorway is far from the corner, then draw a reference line parallel to the doorway near the corner.

Unfold the top of the reserved paper and hang it on the wall. Overlap roughly 2 inches at the ceiling and 1/8 inch in the corner. Gently press it in position.

Unfold the bottom of the novel and let it hang. Check the dimension between the paper and the door casing or reference line. Adjust the paper to keep it parallel to the doorway but still overlapping at ⅛ inch at the corner.

Tuck and Reduce the Paper

Then, working from the top down, sweep the smoother over the entire sheet. (Don’t press so hard that you push glue.)

Trim the excess paper in the ceilingPush a 6-inch taping knife to the joint between the wall and ceiling. With a razor, cut over the knife to cut the excess. Work gradually. Alternate between moving and cutting the knife. Don’t slide the knife and razor together. Keep on papering to a point over the door.

Continue Papering

On the adjacent wall, then draw a plumb line (if there is no door or window).

Hang a strip in the corner. Overlap the present piece on the adjoining wall by 1/8 inch. Measure to the plumb line and correct the paper to maintain the distance equivalent. Smooth the paper. Trim at the ceiling and trim the corner.

Hang the next strip of paper. Unfold the surface of the book and place it on the wall. Match the routine as closely as possible, leaving only a hair’s breadth between the sheets.

Tip: Push out air bubbles by sweeping the newspaper simpler from the middle out to the edges. Wipe off paste on the surface using a sponge.

Close to the Seams

Lightly press on the surface of the paper into the wall. Then gently roll the seam using a seam roller to sew the edges. Now use the ends of your fingers to push the seam shut.

Unfold the bottom of the sheet and complete matching and closing the seam. Then tightly roll down the whole seam, working a full 3 inches from the edge. This locks the seam, keeping it from opening as you smooth the paper.

Smooth the entire sheet. Continue papering the space, overlapping and trimming corners as shown in Step 5.

Suggestion: If the booked end of this strip starts to dry out until you hang it, then wipe the wall with a moist sponge. This will remoisten the glue when you hang the paper.

Cut in About Moldings

At doors and windows, let the paper float the molding by an inch.

Gently run the razor out of the molding corner out to the edge of the paper. Use the molding for a guide.

Press the cut edge tight in the joint between the molding and the wall.

Trim the excess paper flap using a taping knife and razor. Smooth down the whole sheet.

Suggestion: Mistakes are unavoidable once you’re learning how to hang wallpaper. Hide little cutting errors on darker papers by coloring the wall or the white edge of the paper using a mark that matches the newspaper. Some pros even color all of the paper’s edges so seams are not as evident should the paper shrink as it dries.

Cover Switch

Paper the cover plates of electric fixtures to make them vanish. Cut a sheet of wallpaper bigger than the plate. Cut out of the component of the pattern which matches the paper on the wall around the switch.

Hold them both on the wall and correct the paper to match the pattern on the wall.

Hold the paper and turn the plate face down. Cut off the corners 1/8 inch away from the plate. Wrap the paper above the plate and then tape it on.

Cut out the change or receptacle holes using a razor. Make Xs at the screw holes. Screw back the plates to the wall.

發佈留言

發佈留言必須填寫的電子郵件地址不會公開。 必填欄位標示為 *